Aesthetix Calypso Eclipse Linestage

There are four 2uF / 400v coupling capacitors used in each channel of the output stage of the Calypso. In the Eclipse version, these are replaced with Stealth copper foil 4uF/400v, improving low frequency response.

Second phase: High frequency tuning capacitors are installed and hand-adjusted to tailor the frequency response to a tight .1dB standard (as also found on our Signature version).

Third phase: The high voltage transformer, heater transformer and high voltage choke are all re-installed on isolation mounts. Harmonic Resolutions Systems' Nimbus Couplers specially made for Aesthetix replace the four rubber feet of standard units (as also found on our Signature version). The new power supply is installed with enhanced ventilation. Additional damping material is added to key chassis points.

Fourth phase: A single point ground system is used to ground the transformer cases as they are no longer electrically grounded to the chassis via physical contact due to their isolation mounts. All Eclipse Rhea, Calypso and Janus units receive a new power supply, which has been refined by improved trace routing to further reduce extraneous noise.

Technical Specifications:

• Inputs: 5 line RCA or XLR (balanced), plus 1 tape, RCA or XLR
• Outputs: 2 RCA (SE) and XLR (balanced), 1 tape RCA
• Line level gain: 23 dB single ended (SE), in/out, and 29 dB balanced/out
• Volume control: switched resistor network volume control with 88 1 dB steps
• Front panel controls: main input, tape input select, volume, balance, phase, mute, display, and bypass
• Remote controls: main input, tape input select, volume, balance, phase, mute, display, bypass and standby
• Frequency response: +- 0.25 dB, 20 Hz - 20 Khz
• Signal to noise: measured at 70 dB minimum, A-weighted (ref 1 mv input, 75 dB gain setting)
• Line input impedance: 40 k ohms SE, 80 k ohms balanced
• Maximum line input: 3.5 volts SE, 7.0 volts RMS balanced
• Output impedance: 1K ohms SE, 600 ohms balanced
• Recommended amplifier load: 10K ohms or greater (SE), 20K ohms or greater (Balanced)
• Tubes, each channel: (line section) V1 (12AX7 or equivalent), V2 (6922/6DJ8)
• Power consumption: 20 watts standby, 60 watts active
• Physical dimensions: 4 3/8" high, 17 7/8" wide, 18" deep including jacks
• Shipping weight: 40 lbs.

We endeavour to despatch same day for orders placed up to 1pm on available stock items (items with stock message "Usually dispatched within 24 hours"). Please remember to check with us first for a physical stock check if next day delivery is important to you. Any items with stock message "Usually dispatched within 72 hours" are items that we do not hold in stock but order in from the importer or manufacturer as soon as a customer order is received. Occasionally these may be delayed beyond 72 hours due to importer/manufacturer stock levels but we will inform you as soon as we can if this is the case.

UK Orders

We despatch the bulk of our UK mainland items on a 24 hour service – Free of Charge.  Non Mainland locations - Isle of Man, Isle of Wight, the Scilly Isles, the Scottish highlands and Islands, the Channel Islands and Northern Ireland may take a day or so longer and are not Free of Charge. Smaller items are delivered using Royal Mail 24 or special delivery. Larger items are delivered using a courier service such as DPD or UPS.

International Orders:

Due to the nature of our products and brand restrictions we are only able to send certain items internationally. Smaller items are delivered using Royal Mail Small Packets Airmail with International Tracked and/or Signed depending on value of item and availability of the service. Larger International shipments are sent by insured and tracked services using UPS. If there are any delays due to specific customs regulations, etc, you will be contacted by Hifisound or by the courier with a request for any further information required. Customs duties can apply for shipments to any countries outside of the UK depending on where the product you have bought is made. Customers are responsible for all taxes and duties incurred when the items enter their country.

Collect in Store or Home Install

At the request of the manufacturer some items cannot be supplied by mail order but you can click and buy them and then elect to collect them from our store or arrange a home install (if applicable). Applicable items clearly state that they are Collect in store or home install. Once ordered you will receive a message prompting you to contact us by phone or email to arrange for us to deliver and install or to reserve and collect from our store at your convenience, you will also be advised of the delivery time / stock availability as not all Home install / collect in store items are held in stock.